|Whether you're looking at a road, mountain or hybrid bike, there may be a clipless
pedal in your future. But before we get into details, we need to point out why pedals
& shoes are so important, and then define what a clipless pedal is!
The pedals on
your bike really serve only one purpose- as a means to transfer power from you to your
bicycle. For riding around the block, they don't need to be very fancy...just plastic
blocks with grooves or teeth to plant your feet onto. But if you want to go on longer
rides (anything over 10 miles), you'll benefit greatly from something better, because:
- Without something holding your foot securely to the pedal, it would be easy to slip off
the pedal and send your foot into the wheel. Not so likely to happen on a trip around the
block, but on a longer ride, when you're tired...
- There is a correct placement for the position of your foot over the pedal axle
- A good pedal/shoe system has to be able to transfer all of the power from your leg to
the pedals without trying to bend your foot over the top of the pedal, which causes both
fatigue and pain
- You shouldn't have to think about how your feet connect to the bicycle while you're
riding. You should be concentrating on having fun, not technique!
In the old days, bike pedals either were plain (with no straps
to hold your foot in place) or they had toe clips & straps. The toe clip was usually
steel (most are now plastic) and formed a space, or box, at the front side of the pedal
that you slid your foot into. Keeping your foot there is the responsibility of either a
leather or nylon mesh strap, which you can pull tight when you wanted to make sure your
foot stays in place, or loosen so you can get your foot out when you stop.
Toe clips & straps are still the norm for nearly all bikes between $350 and $1000.
They're very inexpensive and don't require the use of a special shoe. But when used with
conventional shoes, they tend to focus pedal forces onto a small part of the bottom of
your foot, creating fatigue & pain on longer rides as your foot tries to bend itself
around the pedal. Also, if the straps are not loosened as you come to a stop...
you go boom! Of course,
you can always leave the straps loose, but then your feet don't stay in place without
conscious effort to keep them on the pedals. And if you've tightened them down, you need
to reach down and loosen them prior to stopping (a somewhat risky operation).
It's time to enter the clipless pedal revolution!
With a clipless pedal system, you wear special cycling shoes
(but don't let "special" put you off...many look similar to normal hiking or
walking shoes!) that allow a "cleat" to be mounted to their sole. This cleat
literally snaps into a receptacle on the pedal, allowing you to quickly (and without
having to reach down!) connect your shoes to the pedals and take off.
But, of course, you weren't worried about taking off...you're more concerned about
stopping without falling over! Well, that's far more easily accomplished with a
properly-chosen and adjusted clipless pedal system than it would be with toe clips &
straps. With nearly every clipless pedal on the market, all you need to do is pivot your
heel outward and you snap right out of the pedals. It's that easy!
What about the shoes? What makes them so special?
A high-quality cycling shoe is designed to be lightweight,
comfortable (some optimizing comfort for both riding and walking, while others are made
for riding only), and efficient at transferring power from you to your bicycle without
pain & fatigue. Popular brands include Shimano, Bontrager & Sidi (which, not
coincidentally, are lines Chain Reaction carries!), and prices range from $70-$350.
Their durability is very good, and the workmanship is generally as good as, and sometimes
better than, normal street shoes selling in the same price range.
different pedal systems?
There are two basic choices-
- Cycling-only pedal/shoe systems, which will have a cleat that mounts below the shoe
and is optimized for cycling (and will send you sliding across the freshly-waxed floors at
Robert's supermarket in Woodside if you're not careful...just grab for something in the
middle of one of those row-end displays on your way down!). These were designed originally
for road bikes, and are inappropriate for mountain bikes, where getting off and walking
- The newer systems featuring a cleat that's recessed into the bottom of the shoe,
allowing you to walk normally when required. These were initially designed for mountain
bikes, but find their way onto more than half of the road bikes we sell as people like the
convenience of being able to walk around without slipping or sounding like a tap dancer
(which is what exposed cleats sound like on wood or concrete floors).
Why would you want a shoe that has an exposed cleat (making walking around impractical)
when you can opt for one that's recessed? Mostly because the shoes will be a bit lighter
weight (there's no extra rubber on the bottom of the sole, just a plastic bottom that the
cleat mounts onto) and also because, with some systems (LOOK, Shimano SL & Speedplay, for example), the interface
between the shoe and pedal is larger and gives a more solid feeling while pedaling.
However, great strides have been made with the recessed cleat designs, and they are now
almost as light and efficient as the non-recessed designs.
What do the pedals cost?
For non-recessed (cycling-only) designs, very high quality pedals
start around $80 for a basic LOOK or Shimano pedal, to $125-$250 for
lighter, more-durable versions (plus Speedplay, which only makes "nicer"
versions). All represent
excellent choices and offer what's known as a "floating" cleat. This type of
cleat is one of the most wonderful things to come along to cycling in years; it allows
your foot and knee to determine their own alignment on the pedal, which is extraordinarily
important in reducing knee stress and pain. Prior to these designs, an improperly-set
cleat could actually cause serious knee injury!
For recessed-cleat designs,
there are a number of designs out there, but it's tough to do much
better than the basic Shimano SPD. Prices have come way down, with just $55 buying a great
pedal (Shimano's M520). Most (includng the M520) are dual-sided, meaning that you can
step in from either the top or bottom, and, while originally designed for mountain bikes,
are equally at home on road bikes. They also have rotational float, which
makes them much easier on the knees than earlier designs.
Great deals that aren't. There are many other recessed-cleat pedals, but we generally don't recommend them
because, in our experience, they are frequently far more difficult to get into and out of
(Onza and Tioga are great examples from the past) and difficult to find cleats for due to continuous
running changes in their designs. We've also seen some copycat Shimano-like pedals made for a major mailorder
company. At first inspection they look pretty nice, but they interface
very poorly with shoes. Check it out...a recessed-cleat pedal/shoe design requires that
the shoe be supported at the outside edges of the pedal to keep from flopping around. But
on these pedals and many shoes we've tried, the sole of the shoe sits well above the
pedal, so the only thing supporting your foot is the tiny cleat itself. This is not enough
for proper support; you get an uncomfortable, excessively-wobbly feel while
pedaling. And they're not even that cheap, at $40/pair...sure, it's
maybe $10 less than some others, but it's a bad place to save a small
amount of money.
Proper cleat placement is important, even
though the new floating-cleat designs have made it far less critical. There are basically
two things to set up- approximate cleat angle and fore/aft positioning.
For the angle, we generally set up the cleats so that, when the shoe is moved inwards,
your ankle won't quite hit the crank. With this position, all the pedal systems we offer
allow a significant outward angle from neutral (in line with the bike), meaning that your
foot can go just about anyplace it wants to. The only reason for changing the cleat
position so it allows less outward movement is for those who have difficulty moving their
heels out far enough to exit the pedals.
For fore/aft, we start by positioning the cleat so the ball of your foot is centered
over the pedal. This position generally results in high energy transfer from foot-to-pedal
without undue stress on the knee. However, for those who've experienced knee problems, the
first thing that should be tried is to move the cleat towards the back of the shoe,
dramatically reducing the amount of leverage that the pedal can exert against your foot
But will I fall over?
OK, we'll finally answer the BIG question. Once you get used to clipless pedals, the
chances of coming to a stop before exiting your pedal (and thus falling over) are greatly
reduced. BUT...chances are, in that first day or two, you'll forget that you need to twist
your foot to the side (instead of pulling back) to get out. By the time you recognize your
mistake, it's too late, as you've lost all forward speed. And, with no place to go but
down...you get the picture. You will, in very slow motion, and nearly always with people
around to see it happen, fall over. You're not likely to get hurt, but it's terribly
embarrassing. And most likely there's nothing that makes you so
special that you'll avoid the fate shared by just about everyone else. Just try and
It's almost impossible to come up with a truly original way to embarrass yourself on a
bike. The rest of us have already, as they say, been there, done that.
FastCounter by LinkExchange
LEARNING HOW TO USE
SPD PEDALS FOR THE FIRST TIME
11/02/2003, "Zelda" asked this question in a newsgroup-
> I bought a good road bike last year, and yesterday I
decided I was
> finally ready to get rid of the old pedals, and get shoes and pedals
> that clip in. I had the bike shop install Shimano SPD pedals, and they
> put my bike in a trainer to let me practice clipping the shoes in and
> out. That was fine. Today, I tried and failed to actually ride my
> bike. I fell twice, hard, without getting out of my driveway. The
> second time, I hit my head on the concrete (yes I was wearing my
Below is my reply-
First off, I don't like introducing people to clipless pedals on a
trainer... it's so far removed from the real world that the lessons learned
about getting into and out of them simply aren't all that relevant. Best
way I've found (and helped several people with today at the shop)-
- Make sure the tension adjustment screws on the pedals
are set as low as possible. Don't back them entirely out though, as
they're impossible to get back in if removed!
- Stand over the bike, without sitting on the saddle
(straddle the top tube). Engage one of the brakes (so the bike doesn't
move around), rotate the pedal you want to get into so it's at about a 7
o'clock position, and, feeling for the front of the cleat engaging with
the pedal, push forward until you hear it snap into place.
Disengage by twisting your ankle outward. Repeat several times until this
feels relatively natural.
- Try the same things with the other pedal, getting used
to what it takes to get into and out of it. More than anything, you're
getting familiar with the location of the cleat on the bottom of the shoe.
- Now it's time to practice while riding. Get one shoe
into the pedal and start off. Don't try getting the other one in too
soon! Get up a little bit of speed so you're stable... it's no big deal
pedaling along for a bit with one foot not engaged. Once you're up to
speed, try getting the other foot into the pedal when it's at that same 7
o'clock position as before. Don't let it frustrate you if engagement is
difficult! Take your time, maybe stop and practice getting that
particular foot in while stopped.
You MUST unclip one of your feet well
before you come to a stop. If you're still clipped in, and you have
no forward momentum, you're going down. As mentioned previously, it's not
difficult pedaling while unclipped for a bit, so plan ahead of time. No
last-second stuff and you'll likely avoid falling.
I suspect the clue to your problems was that you couldn't even get out of
your driveway without falling. You're trying to do too much too fast. Take
things one step at a time and I'll bet it will be easy!