$0.69 - $7.99
White Lightning's Bamboo Cycles Wipes are the quick and easy solution for cleaning your hands, your bike, and anything else you can find. Made from bamboo, Cycle Wipes are tough, durable, and tear-resistant. They have a waffled texture that absorbs more grease and grime than ordinary wipes and are treated with a solution that is strong enough to clean drivetrain parts, plus safe enough to clean your hands, too. White Lightning's Bamboo Cycle Wipes are biodegradable.
Clean your chain in under 20-seconds with White Lightning's The Trigger. Simply close the lid of The Trigger over your chain, spray, and backpedal your chain for about three revolutions. The Trigger comes with one 12-ounce can of Clean Streak so you'll have everything you need for a clean, quiet ride.
- Anti-Loosening, Anti-Corrosion thread prep with PTFE - Two colors offer coating for different spoke lengths
WD-40 Dry Lube is the perfect chain and component lubrication for dry and arid riding conditions. Extensively tested by scientists and pro mechanics alike, it keeps your bicycle shifting like a dream and pedaling smoothly. It boasts special polymers that form a dry film to protect your chain and repel dirt in dry conditions. The result is a clean, quiet, perfectly functioning and long-lasting drivetrain.
WD-40's Frame Protectant is specially formulated to prevent the build-up of dirt, dust and grime on bicycles. Once treated, surfaces stay cleaner longer so your bikes always look great. Plus it helps restores scratched areas and the luster of clear coats on carbon and all other bike finishes, too.
- Removes brake pad material from alloy rims without damaging it - Use just like an eraser
Rock-N-Roll Absolute Dry lubricant is a super-clean chain lube that picks up little or no dirt. - For road bikes only
Rock-N-Roll Extreme is a very clean lubricant due to its ability to shed dirt and dust. - For mountain bike or wet road riding
Rock-N-Roll Gold lubricant is for both mountain and road bike use. The formulation goes deep down into the chain and traps any dirt. Then, with the energy of the chain freewheeling backwards, the dirt and grit floats to the surface so you can wipe it all off, leaving a new and clean application of lube inside the chain, where it's needed. - All-purpose lube - Cleans and lubricates simultaneously
Our best and favorite chain lube. Relatively inexpensive, easy to use, cleans and lubes at the same time. I have never found anything to compare to Rock N Roll Gold. Check out a review of lubes here for more info- https://www.scribd.com/doc/262044061/Velo-Friction-Facts-Chain-Lube-Efficiency-Tests --Mike Jacoubowsky, Partner, Chain Reaction Bicycles
- Premium white grease - Great for bearings and overhauls
Properly install your Ritchey carbon bars and stem without fear of over-torquing with their Torkey. This torque key uses an M4 bit and comes in 2 versions. The 5nm is the maximum recommended torque for Ritchey carbon bars and WCS stems, and the 4nm is for their Break Away frames.
If you own an Air-Bob inflator, you probably use it A LOT. If you need to replace the o-ring for the brass button under the lever, here's the replacement o-ring to get you back up and running.
The Problem Solvers Suspension Pump Adapter is for use with model-year 1999 to 2000 RockShox SID suspension forks. This aluminum adapter threads into the fork to add air and fine-tune the pressure.
- Consumer grade spray cleaner removes dirt and grime - Safe on all parts including carbon
• High quality precision tool; A must for the serious dealer / cyclist! • Adjustability from 3 to 15 Nm; for all stems / handlebars / seatposts etc • Incl. M3, M4, M5, M6, T25 & T30 Chrome Vanadium sockets and extension • Small and easy to use incl. storage-box
Portland Design Works' 3wrencho is a strong and versatile addition to your fixed gear, townie or workbench! Made of heat-treated steel for extra toughness, it's part tire lever, part 15mm wrench. Its strong nylon coating won't scratch rims, so you can pry as hard as you need to remove stubborn tires. Step on the 3wrencho for extra leverage to loosening axle nuts. May also be used to spread peanut butter, stir a drink, or open a letter. - Length: 114 mm (4.5") - Weight: 95 g (3.5 oz)
The BBT-22 is a shop-quality tool for installing and removing Shimano and ISIS Drive splined 20-tooth bottom bracket cups. Made from investment-cast steel, the BBT-22 ensures maximum engagement with the bottom bracket cup. It can be used with a 3/8-inch drive torque wrench, a 3/8-inch ratchet driver, a 32mm wrench, the Park FRW-1 Freewheel Remover Wrench (sold separately), or a 1-inch wrench.
A clean bike is a happy bike! Park Tool's Bike Cleaning Brush Kit is a four-piece brush set designed specifically to clean bicycles. Ergonomically designed and featuring dual-density, sure-grip handles, the BCB-4.2 kit includes: • 1 GSC-1 Gear Clean Brush • 1 Tapered Detail Brush • 1 Frame Cleaning Sponge/Bristle Brush • 1 Soft Bristle Soaping Brush
Bio ChainBrite Bicycle Chain and Component Cleaning Fluid is a 100% biodegradable, natural, plant-based degreaser formulated for use in Park's CM-5.2 Cyclone Chain Scrubber or as a general purpose degreaser. It won't harm alloy, plastic, or rubber parts. Use CB-4 full strength, do not dilute with water. Cover parts in solvent and scrub using a brush. 16-ounce bottle
Park's Lockring Wrench is for installing and removing the adjustable-cup lockring used on Dura-Ace and XTR bottom brackets that use a left-side lockring (it fits several other models and brands of lockrings, too). The Lockring Wrench is laser cut and engages 5 of the lockring's 6 notches for a precise, secure fit. The vinyl-coated handle offers a great grip, too.
Park's BBT-32 is the perfect solution for the home mechanic installing and removing Shimano and ISIS Drive splined 20-tooth bottom bracket cups. Made from investment-cast steel, the BBT-32 utilizes a flat tooth profile to ensure maximum engagement with the bottom bracket cup and features 32mm wrench flats.
Park's BBT-18 is a heavy duty, investment cast tool for installing and removing all Shimano, ISIS Drive, and ISIS Overdrive 8-notch bottom bracket cups.
The BBT-4 is made for the installation and removal of 6-notch SC-S and AC-H cartridge cups used on sealed cartridge bottom brackets. These bottom brackets have six notches around the outside of each cup. The handle of the BBT-4 is vinyl coated for comfort. The major diameter of the tool is nominally 44mm, and the minor diameter 38mm. The BBT-4 is compatible with the following sealed cartridge bottom brackets: • Campagnolo Veloce • Xenon • Mirage • Daytona • Avanti
The BBT-29 is a double-ended bottom bracket wrench designed to fit 16-notch bearing cups with an outside diameter of 39mm (e.g. Shimano Dura-Ace 9000 series and XTR 980 series) as well as 16-notch bearing cups with an outside diameter of 48.5mm (e.g. FSA MegaEvo).
The Bottom Bracket Wrench removes and installs Shimano Hollowtech II, Race Face X-type, FSA MegaExo, Campagnolo Ultra-Torque and TruVativ Giga X-pipe bottom brackets. Laser cut for a precise fit, one end of the BBT-9 securely engages the 16 cup notches, while the other end engages the 8 internal splines of the crankarm adjustment cap.
A dirty drivetrain causes poor shifting and unnecessary wear to expensive parts. The Chain Gang contains everything needed to quickly and easily clean the chain, freewheel cogs, and chainrings. The Chain Gang includes: - CM-5.3 Cyclone Chain Scrubber - GSC-1 GearClean Brush - 8 oz. bottle of Bio ChainBrite The CG-2.4 works on nearly any bike, including multi-speed, single-speed, and e-bikes.
Cleans bicycle chain quickly, easily, and effectively — without the hassle and mess of removing the chain from the bike. The Cyclone uses a large solvent reservoir, hundreds of rotating bristles, and a two-step cleaning process to get chains really clean, improve shifting performance, and extend the life of the chain and other expensive drivetrain parts. - Works with all multi-speed bikes (5, 6, 7, 8, 9, 10, 11, and 12-speed) as well as some single-speed models and e-bikes - Strong magnet at the bottom of the fluid reservoir holds metallic particles scrubbed from the chain - Special wicking sponge draws solvent from the chain as it exits, minimizing drips and mess - Sturdy handle makes the Cyclone easy to use and control - Holds 2 fluid ounces (59ml) of solvent
A professional quality shop chain tool that works on 5-speed to 12-speed Road and Mountain Bike derailleur chains*, including SRAM AXS 12 speed, as well as 1/8-inch and 3/16-inch chains. The CT-3.3 features an adjustable locating shelf so it works on any width chain to remove and install chain rivets. Built to last and easy to use, the CT-3.3 features a comfortable handle, investment cast steel body and replaceable driving pin (#CTP). *The CT-3.3 will install, but not peen, Campagnolo 11 and 12-speed chain rivets. - Comfortable T-handle - Replaceable driving pin (CTP) - Investment cast steel body - Adjustable locating shelf
The Park Tool FR-5.2GT is designed specifically for use when removing and installing cassette lockrings from thru axle hubs. -Utilizes a 12mm guide pin to stabilize the tool during use - Fits 12-spline cassette lockrings from Shimano, SRAM (including 1x), SunRace, SunTour, Chris King and others (23.5mm diameter) - Fits some Shimano and similar disc brake rotor lockrings
Heat treated alloy tool steel, one inch base fits wrench or bench vise. Thin wall construction allows use without removal of cones and locknuts. The FR-5.2G has 12 splines that are approximately 23.4mm across. - Fits Shimano, SRAM, SunRace, SunTour, Chris King and other cassette lockrings - Fits the SRAM XX1 11-speed cassettes - Also Fits Shimano disc brake lockrings - Guide pin stabilizes tool
A worn chain shifts poorly and wears sprockets at an accelerated rate. Park Tool's Chain-Wear Indicator is a “go-no go” gauge designed to accurately indicate when a chain reaches .5% and .75%, the points at which most chain manufacturers suggest replacement. The updated CC-3.2 is longer, more accurate and features permanent measurement markings.
Park's Chainring Nut Wrench makes chainring bolt installation and removal easy. It securely holds the slotted nut to prevent spinning when tightening or loosening the bolt. And, it's double-ended to fit most slotted-type nuts, including Campagnolo chainring bolt nuts.
A favorite of shop mechanics for over 30 year's, Park's CCP-22 Crank Puller removes crankarms that feature square tapers, and those that fit on Power Drive and Power Spline bottom bracket interfaces. The long, comfortable, built-in handle and fine thread provide the leverage needed to remove even the tightest crankarms. And, there's a rotating tip to ensure smooth operation and long life.
Now you can easily tackle any crank bolt with Park's Crank Wrench. It features a dual-sided head with a 14mm socket and 8mm Allen wrench on a long, vinyl-coated handle so you're sure to have the leverage necessary for the job.
Park's Double-Ended Cone Wrenches are designed for home mechanics. They're made of thin tool steel to fit the low-clearance adjusting nuts and cone flats on a variety of bearing assemblies. Each wrench is chrome plated for long life and available in popular combinations from 11 to 18mm. Most applications require a pair of cone wrenches. Call or stop by. We can recommend the correct sizes for your needs.
Also called a sleeping hub, the Dummy Hub slides into rear dropouts and replaces the rear wheel for chain cleaning and transport. The DH-1 works with all derailleur and 1/8" chain. The unique design allows the bike to be shifted and works with open dropout and thru-axle frames up to 12mm.
The Park FR-2 Freewheel Remover fits SunTour two-notch freewheels. It's built thin so that removing axle parts is unnecessary. And, it's constructed of durable heat-treated steel. (Not recommended for use with SunTour 4- and 6-notch freewheels.)
The Park FR-4 Freewheel Remover fits Atom, Regina, splined Zeus and some Schwinn-approved freewheels. It's built thin so that removing axle parts is unnecessary. And, it's constructed of durable heat-treated steel.
The Park FR-6 Freewheel Remover fits most 4-notch BMX and singlespeed freewheels. It can be held with a wrench or vise and its narrow profile allows use without removal of cones and locknuts.
12 splines, 22.6mm diameter fits Shimano, Sachs Aris, Sun Race, DNP Epoch, and other 5–10 speed freewheels. The FR-1.3 includes an enlarged thru-hole to accommodate 14mm axles.
Park's Gear Clean Brush has a handle on one end with a curved, serrated edge perfect for cleaning between cassette cogs. The other end's tough nylon bristles are ideal for cleaning the derailleurs, chain and other drivetrain parts to keep them clean and prevent premature wear. It also works great on brakes and other components that collect dirt and grime. The GearClean easily fits in a toolbox or pack.
Park's Hex Wrenches are every mechanic's best friend. They are constructed from industrial quality steel for durability and feature chamfered tips for a precision fit. And, their convenient L shape is perfect for jobs that require lots of leverage or for getting to hard-to-reach bolts.
The AWS-3 offers 2, 2.5 and 3mm Allen wrenches in a Y shape for excellent leverage. The Allens are vinyl coated for comfort, too.
The AWS-1 is one of Park's most-popular tools because it fits the most-turned bicycle bolts. It features 4, 5, and 6mm Allen wrenches in a Y shape for excellent leverage. Each Allen is vinyl coated for comfort.
Park's Home Mechanic Pedal Wrench is great for your home workshop and event tool box. This top-quality 15mm pedal wrench provides the leverage you need to remove stubborn pedals. It's made to last from heat-treated steel, and the handle has a vinyl grip for comfort.
Park's I-Beam Mini Fold-Up Hex Wrench/Screwdriver/Torx Set with Chain Tool includes 1.5, 2, 2.5, 3, 4, 5, and 6mm Allen wrenches, a socket 8mm Allen, a regular screwdriver, a T25 Torx tool (for disc-rotor bolts), a tire lever, spoke wrenches and a chain tool. The I-Beam conveniently fits in pockets and packs, too.
The I-Beam Mini Fold-Up Set includes 3, 4, 5, and 6mm Allen wrenches, a socket 8mm Allen and regular screwdriver. It's the perfect mini-tool to get you out of binds or make quick adjustments. And, it conveniently tucks into a pocket or pack.
Park's MTB-3.2 Rescue Tool includes a 10-speed compatible chain tool; regular and Phillips screwdrivers; T10, T20, and T25 Torx drivers; 1.5, 2, 2.5, 3, 4, 5, 6, 8mm Allen wrenches; 8, 9, 10mm box wrenches; 3 spoke wrenches; a pedal wrench; a serrated knife; 2 tire levers; and a bottle opener. It's small and light for easy carrying and features durable stainless-steel and nickel-plated tools. Plus, its 3-piece design sports tough nylon handles for an excellent grip.
Park's Rescue Tool is packed with 21 useful tools to easily handle emergency repairs on the road or trail. Tools include 2, 2.5, 3, 4, 5, 6, and 8mm Allen wrenches, 2 tire levers, Phillips and regular screwdrivers, T25 star-shaped driver, 3 spoke wrenches, 8, 9, and 10mm box-end wrenches, a chainring-nut wrench, dust-cap remover, serrated knife, and the all-important bottle opener. Plus, a nylon carrying case with embroidered Park logo is included.
Many chains use a master link that allows the chain to be installed and removed by hand. While master links don't require traditional chain tools, over time, dirt and corrosion can make it difficult to separate them by hand. Park's Master Link Pliers make removing and installing these master links quick and easy. Simply insert the specially sized jaws into the link and squeeze the vinyl-coated handles!
Park's Mini Chain Brute Chain Tool goes anywhere and features a V-shaped handle, a super-strong replaceable pin, and fine threads to make chain removal and installation a breeze. The CT-5 works on any derailleur chain, including Shimano Hyperglide and 9-, 10-, and 11-speed. It works for loosening tight links, too.
Park's PolyLube is specifically formulated to protect bearing components. Its Polyurea grease has extremely high shear strength to protect bottom brackets, headsets, pedals and hubs. Use it on threads, seatposts, stems and cables, too. It's also safe for fork seals, and repels water.
Park’s Professional Cable And Housing Cutter is specifically for use on derailleur and brake cables and housing. It even makes quick work of hard-to-cut shift-cable housing. Its cold-forged, heat-treated-steel handles won't bend and its precision-ground jaws cut perfectly every time. Its dual-density molded grips are specially contoured for superior comfort and control. Plus, there’s a built-in cable-end crimper and a forming hole for reforming housing ends.
Park Tool's Pump Rebuild Kit contains one #1081 head as well as one #1087 plunger gasket for their PFP-3, PFP-6 and PFP-8 floor pumps.
$3.00 - $3.99
Park Tool's Replacement Chain Tool Pin (2-Pack) fits Park Tool's CT-1, CT-2, CT-3, CT-3.2, CT-5, and CT-7 Chain Tools. • Made from hardened alloy tool steel • Uses 7mm or 9/32" 12 pt box end/socket • Sold singly or in pairs
Park Tool's CTP-4K includes four replacement chain tool pins and one 5/32" ball bearing. To replace the chain tool pin, unscrew the cap, and pull out the old pin. Use care not to lose the ball bearing beneath the pin. Install the new pin and replace the cap. Works with the CT-4.3, CT-4.2, CT-4, and CT-11
If you have a bike with disc brakes, you'll want Park's Rotor Truing Fork. It allows you to gently adjust bent and damaged disc-brake rotors. It's made from high-quality steel and features 2 laser-cut slots for precise adjustments and a vinyl handle for comfort and control.
Park's Pin Spanners are designed for maximum usefulness and versatility at the best value. Tough high-carbon tool steel is used to ensure long life and the handles are vinyl coated for a great grip and color-coded for easy identification. The green-handled SPA-1 is used to turn the adjustable bottom-bracket cup found on most 3-piece cranksets.
Park's Cone Wrenches are made of durable tool steel and are nice and thin to fit on the small-clearance cones found on hubs and other bearing assemblies. Plus, they work as regular wrenches, too. They feature Park's special Y heads that put more material where it's needed for excellent durability and strength. This 23mm size fits Shimano 15mm through-axle hubs. Some applications require at least 2 cone wrenches. If you have questions please contact us and we can recommend the correct sizes for your needs.
Page 1 of 5 Next page