Clean your chain in under 20-seconds with White Lightning's The Trigger. Simply close the lid of The Trigger over your chain, spray, and backpedal your chain for about three revolutions. The Trigger comes with one 12-ounce can of Clean Streak so you'll have everything you need for a clean, quiet ride.
- Anti-Loosening, Anti-Corrosion thread prep with PTFE - Two colors offer coating for different spoke lengths
WD-40's Frame Protectant is specially formulated to prevent the build-up of dirt, dust and grime on bicycles. Once treated, surfaces stay cleaner longer so your bikes always look great. Plus it helps restores scratched areas and the luster of clear coats on carbon and all other bike finishes, too.
- Removes brake pad material from alloy rims without damaging it - Use just like an eraser
$10.99 - $29.99
Shimano Hydraulic Disc Brake Fluid - Non-corrosive mineral oil that offers excellent heat expansion properties - Mineral oil will not absorb water from the air - Not caustic and is non-toxic
Rock-N-Roll Absolute Dry lubricant is a super-clean chain lube that picks up little or no dirt. - For road bikes only
Rock-N-Roll Extreme is a very clean lubricant due to its ability to shed dirt and dust. - For mountain bike or wet road riding
Rock-N-Roll Gold lubricant is for both mountain and road bike use. The formulation goes deep down into the chain and traps any dirt. Then, with the energy of the chain freewheeling backwards, the dirt and grit floats to the surface so you can wipe it all off, leaving a new and clean application of lube inside the chain, where it's needed. - All-purpose lube - Cleans and lubricates simultaneously
Our best and favorite chain lube. Relatively inexpensive, easy to use, cleans and lubes at the same time. I have never found anything to compare to Rock N Roll Gold. Check out a review of lubes here for more info- https://www.scribd.com/doc/262044061/Velo-Friction-Facts-Chain-Lube-Efficiency-Tests --Mike Jacoubowsky, Partner, Chain Reaction Bicycles
- Premium white grease - Great for bearings and overhauls
Properly install your Ritchey carbon bars and stem without fear of over-torquing with their Torkey. This torque key uses an M4 bit and comes in 2 versions. The 5nm is the maximum recommended torque for Ritchey carbon bars and WCS stems, and the 4nm is for their Break Away frames.
If you own an Air-Bob inflator, you probably use it A LOT. If you need to replace the o-ring for the brass button under the lever, here's the replacement o-ring to get you back up and running.
The Problem Solvers Suspension Pump Adapter is for use with model-year 1999 to 2000 RockShox SID suspension forks. This aluminum adapter threads into the fork to add air and fine-tune the pressure.
- Consumer grade spray cleaner removes dirt and grime - Safe on all parts including carbon
• High quality precision tool; A must for the serious dealer / cyclist! • Adjustability from 3 to 15 Nm; for all stems / handlebars / seatposts etc • Incl. M3, M4, M5, M6, T25 & T30 Chrome Vanadium sockets and extension • Small and easy to use incl. storage-box
Having trouble getting at internal nipples? Park's 3-Way Internal Nipple Wrench comes to your rescue. It features a 3.2mm square drive, as well as 5 and 5.5mm hex sockets that slip perfectly into the tight surroundings of most rims. It also utilizes Park's innovative Y-shape design that provides heaps of leverage and comfort.
Park combines the three most used bolt sizes into one convenient wrench. The 3-Way Sprocket Wrench sports 8, 9 and 10mm sockets made from forged chrome-vanadium steel in Park's classic Y-shape that offers plenty of leverage and a comfortable grip.
Park Tool introduced the bicycle world to the 3-way hex wrench set over 30 years ago. Our 3-way wrenches fit perfectly in the palm of the hand and provide excellent leverage, making them a favorite of countless shop mechanics worldwide. AWS-1 FEATURES - 4mm, 5mm, and 6mm hex set - Wrenches made from industrial tool steel, through hardened and tempered for long life - Chamfered tips for a perfect fit
The BBT-22 is a shop-quality tool for installing and removing Shimano and ISIS Drive splined 20-tooth bottom bracket cups. Made from investment-cast steel, the BBT-22 ensures maximum engagement with the bottom bracket cup. It can be used with a 3/8-inch drive torque wrench, a 3/8-inch ratchet driver, a 32mm wrench, the Park FRW-1 Freewheel Remover Wrench (sold separately), or a 1-inch wrench.
A clean bike is a happy bike! Park Tool's Bike Cleaning Brush Kit is a four-piece brush set designed specifically to clean bicycles. Ergonomically designed and featuring dual-density, sure-grip handles, the BCB-4.2 kit includes: • 1 GSC-1 Gear Clean Brush • 1 Tapered Detail Brush • 1 Frame Cleaning Sponge/Bristle Brush • 1 Soft Bristle Soaping Brush
Bio ChainBrite Bicycle Chain and Component Cleaning Fluid is a 100% biodegradable, natural, plant-based degreaser formulated for use in Park's CM-5.2 Cyclone Chain Scrubber or as a general purpose degreaser. It won't harm alloy, plastic, or rubber parts. Use CB-4 full strength, do not dilute with water. Cover parts in solvent and scrub using a brush. 16-ounce bottle
Park's Lockring Wrench is for installing and removing the adjustable-cup lockring used on Dura-Ace and XTR bottom brackets that use a left-side lockring (it fits several other models and brands of lockrings, too). The Lockring Wrench is laser cut and engages 5 of the lockring's 6 notches for a precise, secure fit. The vinyl-coated handle offers a great grip, too.
Park's BBT-32 is the perfect solution for the home mechanic installing and removing Shimano and ISIS Drive splined 20-tooth bottom bracket cups. Made from investment-cast steel, the BBT-32 utilizes a flat tooth profile to ensure maximum engagement with the bottom bracket cup and features 32mm wrench flats.
Made from high precision, hardened Cro-Moly steel, Park's Bottom Bracket Tool (External Bearing) can be turned with a 3/8" drive wrench, 1" wrench, or Park Tool FRW-1 Freewheel Remover Wrench (each sold separately).
Park's BBT-18 is a heavy duty, investment cast tool for installing and removing all Shimano, ISIS Drive, and ISIS Overdrive 8-notch bottom bracket cups.
The BBT-4 is made for the installation and removal of 6-notch SC-S and AC-H cartridge cups used on sealed cartridge bottom brackets. These bottom brackets have six notches around the outside of each cup. The handle of the BBT-4 is vinyl coated for comfort. The major diameter of the tool is nominally 44mm, and the minor diameter 38mm. The BBT-4 is compatible with the following sealed cartridge bottom brackets: • Campagnolo Veloce • Xenon • Mirage • Daytona • Avanti
The BBT-29 is a double-ended bottom bracket wrench designed to fit 16-notch bearing cups with an outside diameter of 39mm (e.g. Shimano Dura-Ace 9000 series and XTR 980 series) as well as 16-notch bearing cups with an outside diameter of 48.5mm (e.g. FSA MegaEvo).
The Bottom Bracket Wrench removes and installs Shimano Hollowtech II, Race Face X-type, FSA MegaExo, Campagnolo Ultra-Torque and TruVativ Giga X-pipe bottom brackets. Laser cut for a precise fit, one end of the BBT-9 securely engages the 16 cup notches, while the other end engages the 8 internal splines of the crankarm adjustment cap.
Park's Bottom Bracket/Cassette Tool for Campagnolo is an indispensable tool for your Campagnolo drivetrain. It's for installing and removing all Record, Chorus, Centaur and Athena bottom brackets, and all Campagnolo cassette lockrings.
A dirty drivetrain causes poor shifting and unnecessary wear to expensive parts. The Chain Gang contains everything needed to quickly and easily clean the chain, freewheel cogs, and chainrings. The Chain Gang includes: - CM-5.3 Cyclone Chain Scrubber - GSC-1 GearClean Brush - 8 oz. bottle of Bio ChainBrite The CG-2.4 works on nearly any bike, including multi-speed, single-speed, and e-bikes.
Page 1 of 12 Next page