Tools

Shop quality L-shaped, high torque industrial steel Torx compatible wrenches. Featuring chamfered tips, tight tolerances and a handy portable tool holder for easy access. Includes: T9, T10, T15, T20, T25, T27, T30 and T40.

The DT-5.2 is engineered and built to accurately face front or rear disc brake mounts so they are precisely aligned to the rotor. - Faces any IS Mount, Post Mount, or new Shimano Flat Mount, including low clearance, chainstay mounts - Telescoping axle adaptors allow use with any configuration of open or thru-axle dropouts and dropout widths (including Boost 110, Boost 148 and all fat bike axles) - Includes two facing cutters: IS Mounts Post and Flat Mounts - Includes storage case

With today’s lightweight components, torque wrench use in the shop is no longer an option — it’s a must for every mechanic. The TW-6.2 is a high-quality, ratcheting, click-type torque wrench that accurately measures and applies the proper amount of torque to a component’s threaded fastener(s). Designed for higher torque settings for repairs and installation in the bottom bracket, cassette lockring and other areas that use a higher torque settings. For lower torque setting, see the TW-5. Comes with its own protective case. - 10–60 Newton meter range (88–530 Inch Pounds) - Adjustable in 0.25 Nm increments - Ratcheting 3/8" drive - Reads and registers for both left hand and right hand threading - Dial-adjust system allows desired torque setting to be preset - Calibrated to be accurate to +/- 4% - Length: 36.2cm (14.25")

World-famous Park Tool quality wrapped up in a combination metric wrench. Features both open and 12-point two-way ratcheting box ends. Forged from chrome vanadium steel, chrome plated, meticulously polished, then center dipped in Park Tool blue vinyl for a positive grip. Strong, comfortable, and beautiful!

Designed and built to remove and install the direct mount lockring that retains front chainrings found on some Specialized, Cannondale and FSA modular cranks. - Fits chainring of Specialized, Cannondale and FSA - For lockrings with 47–48mm outside diameter and 4 or 8 notches - Fits both 4 notch (FSA and Cannondale) and 8 notch (Specialized) lockrings - 36mm hex drive to be used with Park Tool TWB-36 Crow Foot and a torque wrench to properly measure torque - Constructed of 4140 heat-treated steel and plated for long life

Professional quality T-Handle hex wrench built for speed, efficiency, leverage and a perfect fit. - Carefully selected combination of Chrome Vanadium and S-2 tool steels - Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless - Machined, chamfered tips allow easier insertion into hex fittings - Integrated “Strip-Gripper” twisted hex that makes removal of most bolts with stripped or oversized hexes fast and easy - Sliding T-handle creates increased leverage and multiple access positions

Forged and machined, the ZP-5 is ideal for closely cutting zip ties and many other materials in tight spaces.

Professional quality T-Handle star-shaped wrench built for speed, efficiency, leverage and a perfect fit. - Carefully selected combination of Chrome Vanadium and S-2 tool steels - Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless - Sliding T-handle creates increased leverage and multiple access positions

A great way to keep the benchtop organized during a repair, the OM-2 features an over-sized textured work area and raised trays for organizing small parts and hardware. Perfect for overhauling or rebuilding components such as forks, shocks, hubs, suspension linkages, derailleurs, etc. - Measures 15 x 24.5-inches (38cm x 62cm) - Interlocking edges allow multiple mats to be joined together - Tear/abrasion/shock-resistant TPR construction

- Don't get stranded. Pack of tire plugs for use with Tubeless Kit or Classic Tubeless Kit - Also available in a pack of 20

A perfect way to start a bicycle tool collection! A great combination of tools to help a home mechanic clean, adjust, maintain, and do some basic repairs on their bike. The SK-4 includes more than 15 genuine Park Tool products that can perform dozens of tasks and includes a custom Park Tool toolbox with extra room for spare parts and more tools. The SK-4 includes: - AWS-10 Fold-Up Hex Wrench Set - BBB-4 Big Blue Book of Bicycle Repair - CC-3.2 Chain Checker - CN-10 Professional Cable and Housing Cutter - CT-5 Mini ChainBrute Chain Tool - FR-5.2 Cassette Lockring Tool - GSC-1 GearClean Brush - HCW-16.3 Chain Whip/Pedal Wrench - HR-8 8mm Hex Wrench - MLP-1.2 Master Link Pliers - SD-2 Shop Screwdriver: #2 Phillips - SW-7.2 Triple Spoke Wrench - TL-1.2 Tire Lever Set - TWS-3 Torx Compatible 3-Way Wrench

Park's Cone Wrenches are made of durable tool steel and are nice and thin to fit on the small-clearance cones found on hubs and other bearing assemblies. Plus, they work as regular wrenches, too. They feature Park's special Y heads that put more material where it's needed for excellent durability and strength. Most applications require at least 2 cone wrenches. If you have questions please contact us and we can recommend the correct sizes for your needs.

The Park FR-3 Freewheel Remover fits SunTour four-notch freewheels. It's built thin so that removing axle parts is unnecessary. And, it's constructed of durable heat-treated steel.

Park's Spoke Wrench For Shimano Wheel Systems is the right tool for the job. It's made of durable tool steel and features 4.4mm and 3.75mm openings to fit all Shimano Wheel System nipples located at the hub and at the rim. It's vinyl-coated for a great grip, too.

This is a single replacement pin for Park Tool HCW-4 and SPA-6 pin spanner wrenches.

Park Tool's Thru Axle Adaptors make it possible to adapt all Park Tool Truing Stands to work with 12mm, 15mm, 20mm, and 25mm thru axle front wheels, as well as Cannondale Lefty wheels (each sold separately). The TS-TA also work with the rear 135mm thru axle hubs in the TS-2.2 and TS-3. The TS-TA when used in the TS-8, TS-25, TS-15, TS-7 or TS-5 will work with all rear thru axle hubs. For thru axle hubs greater than 135 (142, 150, 157, etc.) in the TS-2.2, use the TS-2TA Thru Axle Adaptors (sold separately).

Park Tool's 692 Left-Hand Bottom Bracket Tap is a 1.370" x 24 TPI replacement tap for the BTS-1 Bottom Bracket Tap Set. This tap is used on the drive side (right side) of the bike. This side of the bottom bracket uses a counter-clockwise or left-hand thread. Note: It is very important to have sharp and accurate cutting tools for effective tapping and thread-chasing. Using an excessively worn or damaged tap can cause permanent damage to the frame and/or bottom bracket.

Designed and built specifically for a wide variety of bicycle hex work the THH-1 is a set of eight common sizes of professional quality T-Handle hex wrenches built for speed, efficiency, leverage and a perfect fit. Soon to become your favorite hex set, the THH-1 includes a handy tool holder that mounts to any vertical surface, including pegboard and solid surfaces (fasteners not included). - Carefully selected combination of Chrome Vanadium and S-2 tool steels - 2, 2.5, 3, 4, 5, 6, 8 and 10mm hex wrenches included - Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless - Machined, chamfered tips allow easier insertion into hex fittings - Integrated “Strip-Gripper” twisted hex that makes removal of most bolts with stripped or over-sized hexes fast and easy - Sliding T-handle creates increased leverage and multiple access positions - Tool holder is included with the set and mounts to any wall, bench or tool box, perfectly positioning each wrench for easy access and storage

The QTH-1 is an ergonomic T-handled bit driver equipped with eight common bits to fit a wide variety of fasteners and fittings found on bicycles. The magnetic "quick-change" handle allows for one-handed operation and makes changing bits quick and easy. The bit holder can be magnetically attached to any magnetic surface such as a repair stand or tool box, or can be permanently mounted to any wall or tool board. The QTH-1 is a professional-grade tool built to withstand the rigors of daily shop use and is fully rebuildable. Includes the following magnetic 1/4" bits: - 2mm, 2.5mm, 3mm, 4mm, 5mm & 6mm hex - T25 Torx-compatible - #2 Philips cross tip - Bit holder includes empty spaces for 2 extra bits

Material: premium plus carbon steel, drop forged, entirely hardened and tempered, cutting edges induction hardened

- Blade chrome plated, black anodised tip - Handle – polypropylene

The EP-1 is purpose-built to securely install end caps onto brake, derailleur, and dropper post cables. The short tapered jaws with dual crimping positions make it ideal for crimping in tight, inaccessible spaces. Built from forged machined steel with vinyl-dipped handles.

Performing the right maintenance on your SRAM and RockShox products not only ensures years of worry-free riding, but will also keep performance optimal and enhance your experience on the bike. Each service interval indicates the maximum number of riding hours designated for each type of recommended maintenance. Depending on the terrain and environmental conditions in your location, your riding style, and skill level, you may see more optimum performance if you service your SRAM and RockShox products at shorter intervals.

- Hex wrenches 4, 5, 6 - TX wrench 25 - PH1 screwdriver - Flat screwdriver 1.0 x 5.0

A precision CNC-machined aluminum tool for the installation and removal of select threaded bottom brackets with 16-notch tool fittings, including Wheels Mfg™ Thread Together & FSA® MegaEvo®. Manufactured in-house by Park Tool, anodized for easy identification, and featuring a ratchet/torque wrench-compatible 3/8" drive. Fits 16-notch bottom bracket tool fittings with a major diameter of 48–50 mm and a minor diameter of 46.4 mm, including: - FSA® MegaEvo® - Wheels Mfg™ Thread Together Note: Does not fit Hope™ BSA30

200 HOUR/1 YEAR SERVICE KIT (INCLUDES AIR CAN SEALS, PISTON SEAL, GLIDE RINGS, IFP SEALS, SEAL GREASE/OIL) - SUPER DELUXE THRUSHAFT C1 - TREK (2021)

The DC-2 is a vernier caliper for accurately measuring seat posts, head tubes, bearings, spoke diameters, and other components, featuring a large LCD screen for accuracy and ease of use. The tool’s ability to measure in metric and inches in external, internal, depth, and stepped dimensions make it an indispensable shop tool. - Range: 150 mm | 6" - Resolution: 0.01 mm | 0.0005" - Accuracy: +/- 0.02 mm | 0.001" - Repeatability: +/- 0.01 mm | 0.0005" - Measures external, internal, depth, and stepped dimensions - Uses LR44 batteries

A precision CNC-machined aluminum tool for the installation and removal of select threaded bottom brackets with 36-notch tool fittings, including Praxis Works M35 bottom brackets. Manufactured in-house by Park Tool, anodized for easy identification and featuring a ratchet/torque wrench-compatible 3/8" drive. Fits 36-notch bottom bracket tool fittings with a major diameter of 51–53 mm and a minor diameter of 50.7 mm, including: - Box® Two Oversized M35 - Praxis Works® M35

Refill pack for the Park Tool TPT-1 Tubeless Plug Tire Tool and other similar tools. These vulcanized rubber plugs are used to temporarily repair punctures in tubeless bicycle tire systems. Set of 5. NOTE: Intended for tubeless bicycle tires using sealant only. Not compatible with inner tube systems.

The CT-15 is a professional-grade tool designed to drive rivets in and out of any bicycle chain, from beefy single-speed half-link chains to the latest 13-speed systems. The unique triple-wide floating shelf ensures that every chain is securely fixtured and centered during use. The ergonomic handle stores spare driving pins as well as a peening anvil used for peening Campagnolo® 11, 12, and 13-speed chains. Built for daily use and fully rebuildable. - Compatible with single-speed bicycle chains including 1/8"", 3/16"" and half-link - Compatible with all 5 to 13-speed derailleur chains, including SRAM® 12-speed Flattop™, SRAM® 12-speed T-Type, Shimano® 12-speed XTR®, and Campagnolo® 13-speed Ekar™ - Includes removable anvil for peening Campagnolo® 11 to 13-speed chains - Includes two spare driving pins (part #2987)